●ST-6 Both fan and round pattern
Standard model in ST-6 series.
Used for spraying paints and various kinds of machine oils with a lower air pressure so as to minimize oil scattering. By turning the Pattern Adjuster, the size of the Round to Fan (intermediate possible) pattern can be selected.
●ST-6SK small round pattern model
Small round pattern is good for small area marking and coating a narrow line.
You can coat a small narrow line by moving workpieces or automatic spray guns.
While coating a small area or output a few liquid, masking process is not required.
The minimum pattern is φ2mm.
●ST-6W Wide-Angle fan pattern
Differences between air pressure for atomization and spray pattern allow for spraying a two times wider area with less liquid than the above ST-6 model; Two reducing valves are required.
●ST-6R Round pattern
Used for marking or painting small objects. For spraying round pattern only.
●ST-6RW Wide-Angle Round spraying
Spiral air stream produces a fine granular mist covering a spray angle of approx. 30°, and is able to also paint or coat side walls
(inside of a concave surface) as well as the bottom.
Also, the spiral air stream helps prevent the Air Cap from becoming clogged.
●ST-6PR Jet type, non atomizating type
For lubricating : conveyer chain, gears...etc
To feed oil, the pressured tank is required.
| Model | Spray pattern | Nozzle Orifice φmm |
Flow Rate ㎖/min |
Pattern width mm |
Particle size SMDμm |
Air consumption ℓ/min |
Mass g |
| ST-6 | Round、fan | 0.5 | 0～ 62 | 260 | 28 | 46 | 285 |
| 1.0 | 0～200 | 360 | 39 | 54 | |||
| 1.3 | 0～390 | 420 | 43 | 65 | |||
| 2.0 | 0～570 | 460 | 47 | 76 | |||
| ST-6SK | Small round pattern or narrow line |
0.5 | 0～ 50 | ※2～10 | 29 | 14 | 255 |
| 1.0 | 0～162 | ※2～10 | 32 | 36 | |||
| ST-6W | Wide-angle fan |
0.5 | 0～ 60 | 360 | 14 | 90 | 300 |
| 1.0 | 0～200 | 380 | 14 | 96 | |||
| 1.3 | 0～380 | 400 | 17 | 126 | |||
| ST-6R | Round | 0.5 | 0～ 64 | φ 75 | 32 | 30 | 255 |
| 1.0 | 0～230 | φ 90 | 41 | 35 | |||
| 1.3 | 0～360 | φ 95 | 44 | 40 | |||
| 2.0 | 0～600 | φ100 | 49 | 58 | |||
| ST-6RW | Wide-angle round spiralling spray stream |
0.5 | 0～ 64 | φ100 | 19 | 52 | 255 |
| 1.0 | 0～260 | φ120 | 34 | 66 | |||
| 1.3 | 0～400 | φ140 | 34 | 72 | |||
| 2.0 | 0～600 | φ150 | 34 | 76 | |||
| ST-6PR | Jet, Non-atomatizating | 0.5 | 210 | － | － | 6 | 280 |
※The values in the above table are results obtained through tests under the following conditions:
Fluid : water
Input fluid pressure : applied from a one meter height with a Gravity Feed Container
Maximum Pattern Width : Measured at a 300 mm distance from the tip of spray nozzle
Input Air Pressure : 0.1 MPa
(If the input air pressure is 0.29 MPa, the value will be the same as ST-5 series.)
※ The pattern width value of ST-5SK is under the following conditions :
liquid volume :1.5 ml/min, spray distance from 5 to 20 mm.
※ The model ST-6W measured at atomizating air at 0.1MPa, pattern air at 0.25MPa.
